Terms
Advertise   Support WW    Contact   
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 27
  1. #11
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Go ahead and screw the barbed fitting back on it and its finished.


    Using the ebb n flow screens and hose clamps the finished controller should look something like this i went ahead and installed the shut off valves on this updated system as well!

    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  2. #12
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Part 3 "Prepairing the reservoir"

    Ok this is a easy one,We need to drill a hole in the bottom of the reservoir using the 1&1/4" hole saw bit.

    Now we need to clean the hole up!

    Now install the 1/2" ebb n flow fitting.

    Thats all the reservoir is ready.
    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  3. #13
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Part 4 "Hooking up the system"

    Ok first we need to get the controller in place!

    Now time to place the 1st row and measure out the spacing.

    Ok now that we have figured out the proper spacing,And measured it out we need to pre cut enough for all 4 rows of buckets.This will insure each row is evenly spaced.So pre measure and cut them i needed to run 4 rows so i had to pre cut 8 pieces.

    Now that we have the lines cut and ready we need to go ahead and hook up the 1st row.
    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  4. #14
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times


    Now that the 1st row is hooked up,Time to hook up the shut off valve,This will be installed at the beggining of the row.

    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  5. #15
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Next step is hooking the elbow up to the shut off valve.


    Now connect the row to the controller.

    Now lets hook up row 2.
    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  6. #16
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Now hook up the shut off valve.

    Time to connect the elbow,And run a line from it to the controller.


    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  7. #17
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Lets move onto row 3,We wil be connect the row,Hooking up the shut off valve,Running the tubing from shut of valve to the elbow,From the elbow to the controller,Just repeating the previous steps.


    Time to hook up the 4th and final row for this system,Connect the buckets together hook in the shut off valve,Run line from shut off to elbow,Then from the elbow to the controller,Repeating previous steps again.


    Its time to install the feed lines,But i need a smoke break first
    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  8. #18
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Its time to hook up the feed lines.First off we need to make a little fitting to drop our feed line down even with the return lines.For this i used 2 1/2" OD elbows and some 1/2" ID tubing.

    Now we will connect it to the controller,Should drop it right down level with the 3/4" ID lines.


    Ok next step is to run a line from the fitting,To 1" past the 3/4" OD shut off valve in the 1st row,Then connect a 1/2" OD tee.
    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  9. #19
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times
    Now run a line from the tee to the 3/4" OD shut off valve,Be sure to cut even with it.Then connect the 1/2" ID shut off valve.This will enable us to isolate a row if a problem were to accur,Preventing it from spreading through out the system.

    Now run a line from the tee to 1" past the second rows 3/4" OD shut off valve.Connect another tee,Run line from it up to the 3/4" OD shut off valve and install the 1/2" ID shut off valve for the second row.


    Now we will repeat the previous steps,Run a line from the tee to the 3rd row,Cut off install another tee,Run line from the up to 3/4" OD shut off valve and connect the 1/2" ID shut off valve.
    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

  10. #20
    OG/TSD Refugee
    Join Date
    Mar 2011
    Location
    On my porch toking on my pipe
    Posts
    1,657
    Status
    hippie420 is offline
    Gender
    Male
    Country
    United States
    Liked
    3189 times

    Now we will repeat the previous steps,Run a line from the 1/2" OD tee to the 4th and final row,This time we will be connecting a 1/2" OD elbow to end the run.Then we will run a line from the elbow to the 3/4" OD shut off valve and connect a 1/2" ID shut off valve.


    "There he goes. One of God's own prototypes. A high-powered mutant of some kind never even considered for mass production. Too weird to live, and too rare to die." Hunter S. Thompson
    Overgrow Original | Sp3cialSt3v3420 | 2001 - 2006 | Overgrow The World
    TSD OG 2011-2013 | Hippie420 | Former Forums Manager

Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. Replies: 3
    Last Post: 11-28-2012, 10:27 PM
  2. Water Chemistry (Extremely Detailed and Professional.)
    By hippie420 in forum Hydroponic Cannabis Cultivation
    Replies: 16
    Last Post: 06-07-2011, 05:25 PM
  3. Replies: 2
    Last Post: 06-05-2011, 11:37 AM
  4. Replies: 12
    Last Post: 06-05-2011, 08:17 AM

Tags for this Thread


  
ALL content is for informational and educational purposes only,
and intended for visitors 18 Years of age and Older!


  Copyright ©2007-2019 WeedWatch.com Powered by Cannavelli Brands LLC. Sponsors | Link Partners   xhtml valid   Subscribe to Weed Watch Magazine's RSS Feed   
BACK TO TOP